Short answer
Interlinked alarms sound together when one detects a fire, helping warn people elsewhere in the home. The right system depends on both its power-supply grade and its detection coverage category under BS 5839-6. England’s basic rented-home alarm duties are not the same as a complete system design, and Scotland has wider interlinked alarm requirements for all homes.
Why interlinking matters
A standalone alarm may be difficult to hear behind closed doors, on another floor or at the far end of a long property. Interlinking means activation of one alarm causes the other linked alarms to sound. This provides earlier warning away from the fire’s immediate location. It does not compensate for missing detectors or a poorly planned escape route.
Links can be wired or radio-based, using compatible equipment designed to work together. Radio interlinking can reduce cable disturbance in an existing house, but signals and commissioning must be checked across the actual building. A collection of devices on the same Wi-Fi network is not automatically a suitable interlinked life-safety system. Phone notifications are supplementary, not a substitute for local warning.
Consider who needs to hear or perceive the alarm. People with hearing loss may need compatible vibrating pads, visual alerts or other specialist equipment. Mobility, sleeping arrangements and the route to an exit also affect the design. Tell the installer about those needs before selecting equipment rather than assuming that a louder standard alarm solves every problem.
BS 5839-6 grades: how the system is powered
BS 5839-6 is the domestic fire detection and alarm code of practice. Aico’s published explanation of BS 5839-6:2019+A1:2020 describes grades and categories as separate aspects of a specification. The grade concerns system engineering, including power arrangements; the category concerns where detection is provided. Ask for both to be stated in a design or quotation.
Grade D1 uses mains-powered alarms with a tamper-proof standby battery supply. Grade D2 also uses mains power, but the standby batteries are user-replaceable. Grade F1 uses tamper-proof primary batteries, while Grade F2 uses user-replaceable primary batteries. A sealed battery alarm is therefore not automatically Grade D1: without mains power it may be Grade F1.
Grade A uses a panel-based arrangement with separate detection and warning equipment and standby power. Grade C has a common mains and standby supply with central control equipment. These more involved systems may be appropriate in particular higher-risk properties. Choosing the cheapest grade that sounds an alarm is not a substitute for assessing the building, occupancy and applicable requirements.
LD categories: where detection is provided
Category LD3 provides detection in circulation spaces forming escape routes, such as halls and landings. Category LD2 adds detection in specified rooms or areas presenting a high fire risk to occupants, alongside the circulation spaces. Category LD1 provides detection throughout the dwelling, subject to the standard’s exclusions. Aico’s standards guidance explains these different coverage levels.
The label LD2 alone does not tell you exactly how many alarms a particular house needs. The room layout, circulation routes, open-plan areas and identified risks need review. A kitchen and a principal living room are common considerations in an LD2 design, but the installer should document the locations appropriate to the actual property rather than rely on a generic shopping list.
Building Regulations, licensing conditions and a fire risk assessment can require more than a simple statutory minimum. Extensions, loft conversions and changes to open-plan living may alter the suitable coverage. Do not remove an existing alarm because a general online summary mentions fewer locations. Have the whole arrangement reviewed, including how warning will reach bedrooms at night.
Heat alarms in kitchens and sensible positioning
Kitchens normally call for an appropriate heat alarm rather than a conventional smoke alarm close to cooking fumes. Heat detection reduces nuisance alarms from ordinary cooking while still contributing to fire warning. It does not detect smoke in the same way as a smoke alarm and is not a universal replacement for smoke detection in halls, landings or living rooms.
Use smoke alarms suited to their surroundings elsewhere, with the detector type selected for likely fire characteristics and nuisance sources. Keep locations clear of corners, obstructing beams, air supply grilles and other conditions that can delay detection. Ceiling mounting is usual, but exact distances and permitted positions must follow the system design and manufacturer’s instructions.
Open-plan kitchens, vaulted ceilings and rooms with substantial beams need specific assessment. Fitting one heat alarm in a kitchen area does not automatically protect a connected sleeping or escape space adequately. Never disconnect an alarm to solve repeated nuisance activation. Investigate location, contamination, unsuitable detector type or an expired unit and correct the underlying cause.
Landlord requirements in England
GOV.UK’s guidance on the Smoke and Carbon Monoxide Alarm Regulations explains the duties applying to relevant rented homes in England. Landlords must provide at least one smoke alarm on each storey with a room used as living accommodation. A carbon monoxide alarm is required in rooms used as living accommodation containing a fixed combustion appliance, excluding gas cookers.
The landlord must ensure required alarms work at the start of a new tenancy and repair or replace faulty alarms once informed and the fault is established. Keep evidence of installation, tenancy-start checks and reported faults. Tenants should test alarms regularly in line with instructions and report problems promptly. Agree a clear reporting route rather than leaving responsibility ambiguous.
These regulations do not impose a universal requirement for interlinking or a particular mains-power grade in every existing English rented home. However, licensing conditions, Building Regulations, housing standards and the property’s risks may require a more protective system. Houses in multiple occupation need particular care. Do not present the minimum one-per-storey duty as a complete fire safety specification.
Scotland and other national differences
The Scottish Government states that every home in Scotland must have interlinked fire alarms. The requirements, extended across tenures from February 2022, include a smoke alarm in the living room or most-used room, smoke alarms in hallways and landings, and a heat alarm in the kitchen. The smoke and heat alarms should be ceiling mounted and interlinked.
Scotland permits appropriate mains-wired or tamper-proof sealed-battery interlinked alarms. Its guidance also requires carbon monoxide detection where applicable; the CO alarm does not need to be linked to the smoke alarms. Check the detailed Scottish guidance for open-plan layouts, appliance exceptions and specialist needs. Do not assume an English landlord’s basic alarm arrangement meets Scotland’s standard.
Wales and Northern Ireland also have their own legal frameworks and building standards. This guide’s local landlord discussion is England-focused. If you own property across national borders, obtain a separate specification for each jurisdiction and check the applicable licensing requirements. An alarm package marketed as meeting UK rules is not sufficient evidence of compliance everywhere.
Conversions and period homes in south-east London
Victorian and Georgian houses in Blackheath and Greenwich may have split levels, basements, loft bedrooms and long escape routes. A detector on one landing may not provide timely warning throughout the property. Thick construction can affect radio communication, while decorative cornices and ceilings can make unobtrusive positioning difficult. Surveying these features early helps avoid an unsuitable off-the-shelf layout.
Converted houses in Lewisham, Lee and Catford raise additional questions about separation between flats and the strategy for common areas. Do not simply link every flat and communal detector together. In purpose-built blocks, communal detection and evacuation arrangements need particular care and may be governed by a different design standard. Coordinate changes with the responsible person, managing agent or competent fire safety adviser.
Radio-linked equipment can reduce disturbance to original plasterwork where the selected grade and legal requirements allow it. Where mains circuits are altered, agree electrical certification and any applicable Part P notification. Freeholder permission and listed building considerations are separate from alarm performance. A sensitive installation should preserve important fabric without compromising detection, access for testing or audibility.
Installation, testing and replacement planning
Ask for a written specification showing grade, category, detector types, locations and interlink method. Confirm that every component, including bases, radio modules and specialist warning devices, is compatible. At commissioning, test that activation produces the intended warning throughout the system. Keep installation and commissioning records, instructions and electrical certificates where relevant with the property’s safety documents.
Test alarms using their test controls as directed by the manufacturer, and record checks in rented or managed accommodation. Check the link as well as the individual sounder. Clean units as instructed and note replacement dates; many domestic alarms have a service life around ten years, but the marked expiry and manufacturer’s requirements govern the actual replacement interval.
A sealed battery avoids routine battery replacement, not eventual alarm replacement or the need for testing. Mains alarms also need functioning standby supplies. Chirping may indicate a battery, expiry or fault condition and should be investigated rather than silenced permanently. If there is a fire or an alarm suggests a real emergency, leave safely and call 999; do not stay inside troubleshooting equipment.
When to call a registered electrician
- You need mains-powered alarms installed, replaced or connected to an existing circuit.
- An alarm loses mains power, reports a persistent fault or fails its test.
- A loft conversion, extension or changed layout may affect detection and escape routes.
- The existing alarms do not sound together or their compatibility is uncertain.
- A rented home needs a documented system review beyond basic tenancy-start checks.
- Period ceilings, shared areas or hearing needs require a carefully coordinated design.
David J Farrar & Associates are Part P, NAPIT and NICEIC registered with over 35 years' experience across Blackheath, Lewisham, Greenwich, Bexley and North Kent. Call 07977 519533 or send an enquiry for a free, fixed quotation.
Related services
- Fire Alarms & Smoke Detection — Mains-powered, interlinked smoke, heat and carbon monoxide alarms for homes, rentals and businesses.
- Landlord Safety Certificates — EICRs for rented homes, HMOs, flats and house shares — with fast remedial work if needed.
- Repairs, Maintenance & Fault Diagnosis — Tracing trips, dead circuits, burning smells and flickering lights — and fixing them properly.
Frequently asked questions
Do all alarms in an English house have to be interlinked?
There is no single retrospective interlinking rule for every existing owner-occupied English home. Building work, rental licensing and risk-based requirements can change what is needed. Interlinking is a valuable improvement and is required in many specified designs.
Can a kitchen heat alarm replace the landing smoke alarm?
No. The devices serve different detection needs and locations. A heat alarm in a kitchen should form part of the overall design, not remove smoke detection from the escape route.
Can different alarm brands be linked?
Only where the manufacturers explicitly confirm compatibility for the particular models and connection method. Similar connectors, radio frequencies or app features do not establish safe compatibility.
Is an EICR proof that the alarm system complies?
No. An EICR assesses the fixed electrical installation within its agreed scope. It is not a substitute for an appropriate fire alarm design, commissioning record and functional testing of the detection system.
Does a CO alarm need to be interlinked?
Not automatically. Carbon monoxide detection has a different purpose and applicable requirements. Scottish guidance specifically says the CO detector need not link to the smoke alarms. Compatible combined systems should clearly distinguish the warning types.
Official sources
Need this sorted? Get a free, fixed quote from a registered local electrician.
07977 519533Enquire onlineThis guide is general information about UK electrical regulations and good practice, and any prices are indicative only. For advice on your property, speak to a registered electrician.

